Wheels

Whisky Parts Co. Tubeless Rim Tape.

- Anodized aluminum - 50 nipples per bag - 12mm length

- Cold forged 304 stainless steel with rolled threads - Lightweight 2.0mm/1.7mm/2.0mm double-butted form - Nipples sold separately - 172g (32 spokes @ 262mm) - Bag of 50

- Cold forged 304 stainless steel with rolled threads - Lightweight 2.0mm/1.7mm/2.0mm double-butted form - Nipples sold separately - 172g (32 spokes @ 262mm) - Bag of 50

- Cold forged 2.0mm 304 stainless steel with rolled threads - Nipples sold separately - 213g (32 spokes @ 262mm) - Bag of 50

- Cold forged 2.0mm 304 stainless steel with rolled threads - Nipples sold separately - 213g (32 spokes @ 262mm) - Bag of 50

Rims: WTB EZR i23 700C - ETRTO 622-23 - Inner width: 23mm - Made from 6069 series Aluminum alloy - Asymetric and angled spoke hole drilling distributes spoke tension more evenly - Stronger and lighter rim using a sleeved joint - Disc Brake Only - Drilled for Presta valve - TCS 2.0 Tubeless System compatible - Solid Strip (included) - 32 holes Front hub: Shimano 105 HB-RS7070 - 12x100mm E-THRU (Axle not included) - Center Lock Disc Mount - Polished angular contact bearings with Internal Grease Sleeve - Contact sealed hub Rear hub: Shimano 105 FH-RS7070 - 12x142mm E-THRU (Axle not included) - Center Lock Disc Mount - Polished angular contact bearings with Internal Grease Sleeve - Contact sealed hub and freehub body - Compatible with 11 speed Road (10 speed compatibility requires 1.85mm spacer, not included) - Assembled in North America by experienced wheelbuilders with Sapim Race Butted Stainless Steel spokes (Black) and 14mm Brass Polyax Nipples (Black)

Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

- Shell: 8mm flanged axle nut - Flanged

Replacement clear plastic spoke guard.

- Replacement steel quick release skewers

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Best seller. You'll be hard-pressed to find a better wheel anywhere near these prices.

• Size: 26 x 4.0 • Double wall construction • Non-machined sidewall • Color: Black • Drilling: 32 or 36 • ERD: 534 • Width: 80mm • Depth: 24.5 • Weight: 1,310 grams (32-hole), 1,294 grams (36-hole)

Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable

Get rolling again with a replacement freehub body for your Mavic wheels. - For Mavic ID360 hubs

Grade 10 chromium steel balls

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

SILCA valve stem extenders for tubular tires and tubes with removable valve core. ENVE recommends that the length of your tire/tube valve + the length of your extender exceeds the depth of the rim by at least 10mm. - The 34mm set is optimized for the SES 3.4 and SES 3.4 Disc - The 45mm set is optimized for the SES 4.5 and SES 5.6 Disc - The 75mm set is optimized for the SES 7.8 and SES 7.8 Disc

Replacement freehub spoke protector, in various sizes for different freehub sizes. - Made of clear plastic - 3 hooks for affixing to spokes

Champion 2.0 Black Spokes - One 264mm spoke = 7g

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - Compatible with straight pull hubs only - One 264mm spoke = 5.9g - Nipples sold separately

A 30mm welded Enduro rim developed for the fastest EWS rider. Enduro may be young as a discipline, but at its core is the intrinsic need of riders to ride burlier terrain faster and faster. Something that MTB has been all about since the beginning. The EX 511 rim is the perfect tool for this quest. It comes with all the technology that has delivered many EWS wins and packs it in a 30mm-wide profile, ready to go burlier, faster.

Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included

Steel